WranglerIncludes Wrangler UnlimitedChrysler Group LLC OWNER’S MANUAL 2013 Wrangler13JK72-126-AB Second Edition Printed in U.S.A.2013Information Provi
WARNINGS AND CAUTIONSThis Owners Manual contains WARNINGS against op-erating procedures that could result in a collision orbodily injury. It also cont
WARNING!• An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchorage position dir
For the recommended viscosity and quality grades, referto “Maintenance Procedures” in “Maintaining Your Vehi-cle”. NON-DETERGENT OR STRAIGHT MINERALOI
Exhaust GasWARNING!Exhaust gases can injure or kill. They contain carbonmonoxide (CO), which is colorless and odorless.Breathing it can make you uncon
to seep into the passenger compartment. In addition,inspect the exhaust system each time the vehicle is raisedfor lubrication or oil change. Replace a
Floor Mat Safety InformationAlways use floor mats designed to fit the footwell of yourvehicle. Use only floor mats that leave the pedal areaunobstruct
Periodic Safety Checks You Should Make OutsideThe VehicleTiresExamine tires for excessive tread wear and uneven wearpatterns. Check for stones, nails,
Information Provided by:
UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 MIRRORS ...111▫ Inside Day/Night Mirror ...111▫ Outside Mirr
▫ Delete/Erase “All” Uconnect™ PhonebookEntries ...124▫ List All Names in the Uconnect™ Phonebook. .125▫ Phone Call Features
▫ Replacing The Rear Seat— Two-Door Models ...164▫ 60/40 Split Folding Rear Seat — Four-DoorModels ...164䡵 TO
NOTE: It is illegal to remove or alter the VIN plate.VEHICLE MODIFICATIONS/ALTERATIONSWARNING!Any modifications or alterations to this vehicle couldse
▫ To Set A Desired Speed ...179▫ To Deactivate ...180▫ To Resume Speed ...180▫ To Vary The Speed
▫ Front Panel(s) Installation With Rear HardTop Removed ...210▫ Rear Hard Top Removal ...210▫ Rear Hard Top Installa
䡵 FOLDING WINDSHIELD ...286▫ Lowering The Windshield And RemovingSide Bars ...288▫ Raising The Windshield And Re
MIRRORSInside Day/Night MirrorA two-point pivot system allows for horizontal andvertical adjustment of the mirror. Adjust the mirror tocenter on the v
Outside MirrorsTo receive maximum benefit, adjust the outside mirror(s)to center on the adjacent lane of traffic with a slightoverlap of the view obta
Power Mirrors — If EquippedThe power mirror switch is located on the center of theinstrument panel, below the climate controls. A rotaryknob selects t
Vanity MirrorsVanity mirrors are located on the sun visors. To use themirrors, rotate the sun visor down and swing the mirrorcover upward.Uconnect™ Ph
For Uconnect™ customer support, visit the followingwebsites:• www.chrysler.com/uconnect• www.dodge.com/uconnect• www.jeep.com/uconnect• or call 1–877–
Uconnect™ Phone ButtonThe radio or steering wheel controls (ifequipped) will contain the two control buttons(Uconnect™ Phonebutton and VoiceCommandbut
OperationVoice commands can be used to operate the Uconnect™Phone and to navigate through the Uconnect™ Phonemenu structure. Voice commands are requir
Information Provided by:
Help CommandIf you need assistance at any prompt, or if you want toknow your options at any prompt, say “Help” followingthe beep. The Uconnect™ Phone
• You will be asked to say a four-digit Personal Identi-fication Number (PIN), which you will later need toenter into your mobile phone. You can enter
Call by Saying a Name• Press the button to begin.• After the “Ready” prompt and the following beep, say“Call”.• The system will prompt you to say the
After you are finished adding an entry into the phone-book, you will be given the opportunity to add morephone numbers to the current entry or to retu
• Only the phonebook of the currently connected mobilephone is accessible.• Only the mobile phone’s phonebook is downloaded.SIM card phonebook is not
Edit Uconnect™ Phonebook EntriesNOTE:• Editing names in the phonebook is recommendedwhen the vehicle is not in motion.• Automatic downloaded phonebook
• After you enter the Phonebook Delete menu, you willthen be asked for the name of the entry that you wishto delete. You can either say the name of a
List All Names in the Uconnect™ Phonebook• Press the button to begin.• After the “Ready” prompt and the following beep, say“Phonebook List Names”.• Th
Answer or Reject an Incoming Call - CallCurrently in ProgressIf a call is currently in progress and you have anotherincoming call, you will hear the s
Conference CallWhen two calls are in progress (one active and one onhold), press and hold thebutton until you hear adouble beep indicating that the tw
THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A WORD ABOUT YOUR KEYS ...14▫ Ignition Key Removal ...14▫ Key-In-Igniti
Call ContinuationCall continuation is the progression of a phone call on theUconnect™ Phone after the vehicle ignition key has beenswitched to OFF. Ca
Emergency AssistanceIf you are in an emergency and the mobile phone isreachable:• Pick up the phone and manually dial the emergencynumber for your are
WARNING!To use your Uconnect™ Phone System in an emer-gency, your mobile phone must be:• turned on,• paired to the Uconnect™ System,• and have network
Voice Mail CallingTo learn how to access your voice mail, refer to “Workingwith Automated Systems”.Working with Automated SystemsThis method is used i
NOTE:• You may not hear all of the tones due to mobile phonenetwork configurations. This is normal.• Some paging and voice mail systems have system ti
Dialing Using the Mobile Phone KeypadYou can dial a phone number with your mobile phonekeypad and still use the Uconnect™ Phone (while dialingvia the
Advanced Phone ConnectivityTransfer Call to and from Mobile PhoneThe Uconnect™ Phone allows ongoing calls to be trans-ferred from your mobile phone to
• You can also press the button at any time whilethe list is being played, and then choose the phone thatyou wish to select.• The selected phone will
You can either press the Uconnect™ Phone button torestore the factory setting or repeat the words andphrases when prompted by the Uconnect™ Phone. For
• Even though the system is designed for users speakingin North American English, French, and Spanish ac-cents, the system may not always work for som
▫ Programming Additional Transmitters...26▫ General Information ...26▫ Transmitter Battery Replacement ...27䡵 REMOTE STA
• Performance, such as audio clarity, echo, and loudnessto a large degree rely on the phone and network, andnot the Uconnect™ Phone.• Echo at the phon
Send Messages:You can send messages using Uconnect™ Phone. To senda new message:• Press thebutton.• After the “Ready” prompt and the following beep, s
16. Can this wait?17. Bye for now18. When can we meet19. Send number to call20. Start without meTurn SMS Incoming Announcement ON/OFFTurning the SMS I
3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141Information Provided by:
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Provided by:
3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143Information Provided by:
Voice CommandsPrimary Alternate (s)zeroonetwothreefourfivesixseveneightninestar (*)plus (+)pound (#)add locationallVoice CommandsPrimary Alternate (s)
Voice CommandsPrimary Alternate (s)languagelist nameslist phonesmobilemutemute offnew entrynootherpair a phonephone pairing pairingphonebook phone boo
General InformationThis device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•
When you press the Voice Command button, youwill hear a beep. The beep is your signal to give acommand.NOTE: If you do not say a command within a fews
▫ Adjustable Upper Shoulder Belt Anchorage . . .55▫ Seat Belts In Passenger Seating Positions ...56▫ Automatic Locking Retractor Mode (ALR)— If Equ
CommandsThe Voice Command system understands two types ofcommands. Universal commands are available at alltimes. Local commands are available if the s
• “Previous Station” (to select the previous station)• “Radio Menu” (to switch to the radio menu)• “Main Menu” (to switch to the main menu)Radio FMTo
DiscTo switch to the disc mode, say “Disc”. In this mode, youmay say the following commands:• “Track” (#) (to change the track)• “Next Track” (to play
• “Change to setup”• “Main menu setup” or• “Switch to setup”In this mode, you may say the following commands:• “Language English”• “Language French”•
SEATSSeats are part of the Occupant Restraint System of thevehicle.WARNING!• It is dangerous to ride in a cargo area, inside oroutside of a vehicle. I
WARNING!• Adjusting a seat while driving may be dangerous.Moving a seat while driving could result in loss ofcontrol which could cause a collision and
Manual Seat Height Adjustment — If EquippedThe driver’s seat height can be raised or lowered by usingthe ratcheting handle, located on the outboard si
WARNING!Do not ride with the seatback reclined so that theshoulder belt is no longer resting against your chest.In a collision you could slide under t
To return the seat to a sitting position, rotate the seatbackupright until it locks and push the seat rearward until thetrack locks.NOTE:• The front p
Tip n’ Slide Seats — Two-Door ModelsThis feature allows the front seats to be rotated toward theinstrument panel to allow easier entry into the rear s
A WORD ABOUT YOUR KEYSThe keys for your new vehicle are enclosed in a plasticbag with the key code number on it. If you received yourkeys without the
Passenger SeatIn addition to Easy Entry, the front passenger seat is alsoequipped with Tip n’ Slide. This feature allows for easierentry for rear pass
Heated Seats — If EquippedOn some models, the front driver and passenger seatsmay be equipped with heaters in both the seat cushionsand seatbacks.Ther
WARNING!• Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes,spinal cord injury, medication, alcohol us
Front Head RestraintsTo raise the head restraint, pull upward on the headrestraint. To lower the head restraint, press the adjust-ment button, located
1. Lift the seatback release lever and fold the seatbackforward.2. Slowly flip the entire seat forward.3. Return the seat to the normal position.4. Ra
Removing The Rear Seat — Two-Door ModelsWARNING!• It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, pe
Replacing The Rear Seat — Two-Door ModelsReverse the steps for removing the seat.WARNING!• To help protect against personal injury, passengersshould n
To Fold Down The Rear SeatLocate the pull strap (lower outboard side of seat), andpull it toward you until the seatback releases.To Raise The Rear Sea
TO OPEN AND CLOSE THE HOODRelease both the hood latches.Raise the hood and locate the safety latch, located in themiddle of the hood opening. Push the
LIGHTSMultifunction LeverThe multifunction lever controls the operation of theparking lights, headlights, headlight beam selection,passing light, fog
3. Push the ignition key inward.4. Turn the ignition key to the LOCK position, andremove the key.WARNING!• Before exiting a vehicle, always apply the
Automatic Headlights — If EquippedThis system automatically turns the headlights on or offaccording to ambient light levels. To turn the system on,tur
Turn SignalsMove the multifunction lever up or down and the arrowson each side of the instrument cluster flash to showproper operation of the front an
Lights-On ReminderIf the headlights or parking lights are left on after theignition is turned OFF, a chime will sound to alert thedriver when the driv
Rotate the center portion of the lever upward to the nextdetent position to brighten the odometer and radio whenthe parking lights or headlights are o
Cargo LampThe courtesy and dome lights will turn on when the frontdoors are opened, by rotating the control for the dimmerswitch on the multifunction
When a door is open and the interior lights are on,rotating the dimmer control to the extreme bottom posi-tion will cause all the interior lights to t
Windshield Wiper OperationRotate the end of the lever upward to the second detentpast the intermittent settings for low-speed wiper opera-tion. Rotate
NOTE: The wiper delay times depend on vehicle speed.If the vehicle is moving less than 10 mph (16 km/h),delay times will be doubled.Windshield Washers
Mist FeaturePush down on the wiper lever to activate a single wipe toclear off road mist or spray from a passing vehicle. Aslong as the lever is held
TILT STEERING COLUMNThis feature allows you to tilt the steering columnupward or downward. The tilt lever is located on thesteering column, below the
Key-In-Ignition ReminderOpening the driver’s door when the key is in the ignitionsounds a signal to remind you to remove the key.NOTE: The Key-In-Igni
WARNING! (Continued)the driver to lose control of the vehicle. Be sure thesteering column is locked before driving your ve-hicle. Failure to follow th
NOTE: In order to ensure proper operation, the Elec-tronic Speed Control System has been designed to shutdown if multiple Speed Control functions are
To DeactivateA soft tap on the brake pedal, pushing the CANCELbutton, or normal brake pressure while slowing thevehicle will deactivate Electronic Spe
Pressing the SET (-) button once will result ina1mph(1.6 km/h) decrease in set speed. Each subsequent tap ofthe button results in a decrease of 1 mph
ELECTRICAL POWER OUTLETThere are two 12 Volt (13 Amp) auxiliary power outletsthat can provide power for accessories designed for usewith the standard
A second power outlet is located inside the center consoleand is powered directly from the vehicle battery.CAUTION!• Do not exceed the maximum power o
WARNING!To avoid serious injury or death:• Only devices designed for use in this type of outletshould be inserted into any 12 Volt outlet.• Do not tou
CAUTION!• Many accessories that can be plugged in drawpower from the vehicle’s battery, even when not inuse (i.e., mobile phones, etc.). Eventually, i
POWER INVERTER — IF EQUIPPEDThere is a 115 Volt, 150 Watt inverter outlet located on thefront of the center console to convert DC current to ACcurrent
inverter should automatically reset. If the power ratingexceeds approximately 170 Watts, the power invertermay have to be reset manually. To reset the
CAUTION!The Sentry Key威 Immobilizer system is not compat-ible with some after-market remote starting systems.Use of these systems may result in vehicl
CUPHOLDERSFront CupholdersThe front cupholders are located in the center console.Rear CupholdersThe rear cupholders are located on the back of the cen
STORAGEGlovebox StorageThe lockable glovebox storage compartment is located onthe passenger side of the lower instrument panel. Pulloutward on the han
Rear Storage CompartmentThe rear cargo area storage compartment cover is held bya spring-loaded latch. In order to remove the rear storagecompartment
DUAL TOP — TWO-DOOR MODELS —IF EQUIPPEDIf your vehicle is equipped with a Dual Top, you mustremove one of the tops from the vehicle. If the soft topis
3.Remove the soft top bow assembly pivot bracket screws(two per side) using a #T30 Torx威 head driver.4. Disconnect the knuckles from the left and righ
6. Reinstall the hard top. Refer to “Freedom Top Three-Piece Modular Hard Top — Front/Rear Panel Instal-lation” in this section.Installing The Soft To
3. Install the door frames. Refer to “Door Frame” in thissection.4. If the soft top has been removed, follow these steps toreinstall the soft top. If
NOTE: To aid in reattaching the knuckles, you maycarefully tap on the knuckles using a rubber mallet.4. Screw the pivot screws back into place using a
1. Remove the swing gate bar (black metal bar forbottom of rear window) and set aside.NOTE: Be sure the wire harness in the left rear corner isnot tan
Removing The Soft Top — Four-Door Models1. Locate and remove the two boxes that contain thefollowing items:• Right and left door frames• Six door fram
VEHICLES SOLD IN CANADAWith respect to any Vehicles Sold in Canada, the nameChrysler Group LLC shall be deemed to be deleted and thename Chrysler Cana
Customer Key ProgrammingIf you have two valid Sentry Keys威, you can programnew Sentry Keys威 to the system by performing thefollowing procedure:1. Cut
4. Slide the tether strap up the side bow and attach topivot bracket to secure side bows before removing softtop (both sides).5. Remove the soft top b
Remove the soft top from the vehicle and store in a clean,dry location (another person may be needed to help withthis operation).7. Reinstall the hard
4. Install the soft top with the pivot bracket above thesport bar bracket, lower the pivot bracket onto thesport bar bracket mounting tab in a downwar
CAUTION!Do not overtighten the screws. You can strip thescrews if they are overtightened.6. Remove the tether strap from the pivot bracket andslide do
9. Unsnap and remove the black boot cover. This covershould be discarded. It was intended as a protectivecover for shipping only.NOTE: A visual instru
CAUTION! (Continued)• The hard top assembly must be positioned prop-erly to ensure sealing. Improper installation cancause water to leak into the vehi
3. Turn the center L-shaped locks (two) from the centerof the roof panel.4. Turn the rear L-shaped lock (located above the shoul-der belt anchorage).2
5. Unlatch the header panel latch located at the top of thewindshield.6. Remove the left-hand panel.To remove the right panel, follow the steps abovee
Insert the right side Freedom panel into the bag with thelatches facing downward.Unfold the black panel divider (ensure the divider islaying flat). Se
Insert the left-side Freedom panel into the bag with thelatches facing upward.NOTE: Ensure the front Freedom panel latch is closedprior to inserting t
NOTE: If a programmed key is lost, see your authorizeddealer to have all remaining keys erased from the sys-tem’s memory. This will prevent the lost k
Install the seat attachment strap (at the top of the bag)through the loops.Lift the Freedom bag into the vehicle with the hooks andstraps facing the b
Wrap the upper strap around the rear head restraints andloop the strap through the buckle. Pull on the strap totighten the Freedom bag securely agains
Front Panel(s) Installation With Rear Hard TopRemoved1. Turn the left and right panels over and move thespacer block (located on the rear of the panel
4. Remove the six Torx威 head screws that secure the hardtop to the vehicle (along the interior bodyside) using a#40 Torx威 head driver.5. Open the swin
7. Release the red locking tab by pulling outward to theright.8. To remove the wiring harness press the tab and pulldownward to disconnect.Red Locking
9. To remove the washer hose, pinch the grips on hoseconnector and pull downward.10. Close the swing gate.11. Remove the hard top from the vehicle. Pl
Make sure that the hard top is sitting flush with the bodyat the sides and check to ensure that there is a uniformgap between the lift glass and hard
CAUTION! (Continued)• Careless handling and storage of the removabledoor frame(s) may damage the seals, causing waterto leak into the vehicle’s interi
2. Place one hand on the upper rear and one hand on thefront of the door frame.3. Pull the frame toward you with your rearward hand toremove the frame
Door Frame Installation — Two-Door Models1. Unfold door frame and unscrew thumbscrews.2. Set the door frame pin into the hole on top of the bodyside,
Rearming The SystemIf something triggers the alarm, and no action is taken todisarm it, the Vehicle Security Alarm will turn off thehorn after three m
5. Starting with the front knob, screw in and tighten bothknobs. Repeat on the other side.Door Frame Installation — Four-Door Models1. Install the rea
3. Position the top of the door frame against the metalsport bar and press onto the side bar making sure notto pinch the material of the sports bar co
6. Clip the front of the door rail over the side bar makingsure that the material for the side bar cover is notpinched by the door frame.7. Position t
SOFT TOP — TWO-DOOR MODELSPlease visit the owners section of Jeep.com for instruc-tional videos.CAUTION!The soft top is not designed to carry any addi
CAUTION! (Continued)• Refer to “Appearance Care For Fabric Top Models”in “Maintaining Your Vehicle” for further informa-tion. It contains important in
CAUTION!Failure to follow these cautions may cause interiorwater damage, stains or mildew on the top material:• It is recommended that the top be free
2. Remove the back window. 3. Release header latches from the windshield frame.224 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Provided by:
4. Release the sail panel retainers from the body sidechannel at the rear corners of the vehicle.NOTE: When releasing the sail panel retainers, it ish
6. Release the Sunrider威 latch (both sides). 7. Open the swing gate and lower the top.NOTE: Ensure fabric does not overhang the sides of thevehicle.22
Quick Steps To Raising The Soft TopRefer to “Raising The Soft Top” in this section for furtherinformation.1. Open the swing gate and raise the top, en
the alarm will sound. If this occurs, press the UNLOCKbutton on the RKE transmitter to disarm the VehicleSecurity Alarm. You may also accidentally dis
2. Engage header latches. 3. Install rear corner panels.228 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Provided by:
4. Install the back window. 5. Install the side windows.3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229Information Provided by:
6. Insert the front retainer of the window into the doorchannel, making sure the retainer is fully seated andproperly positioned on the door frame. Fa
Lowering The Soft Top1 — Header Bow 6 — Quarter Window2 — 2–Bow 7 — Check Strap3 — 3–Bow 8 — Front Retainer — Quarter Window4 — Sail Panel 9 — Bottom
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail Panels232 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Pro
NOTE: Clean side and rear windows before removal toassist in preventing scratching during removal of the softtop. If zippers are difficult to operate
5. Before unzipping the rear window, release the first 3 in(7.6 cm) of both sail panels from the channel. Removethe swing gate bar by pulling it strai
6. Remove the rear window retainer from the swing gatebracket on both the left and right sides.7. Stow the windows carefully to avoid scratching.8. Un
11. Finish releasing the sail panel retainers from the bodyside channel at the rear corners of the vehicle.NOTE: When releasing the sail panel retaine
13. The swing gate brackets do not need to be removedunless the hard top is being installed. To remove theswing gate brackets, pull the front of the b
REMOTE KEYLESS ENTRY (RKE) —IF EQUIPPEDThis system allows you to lock or unlock the doors, swinggate, and activate the Panic Alarm from a maximumdista
15. Make sure the plastic sleeves are slid rearward overthe Sunrider威 link (Sunrider威 Models only).16.Unlatch the side bows from both door rails (Sunr
17. Before lowering the top, open the swing gate toprevent possible damage to the rear center high-mounted brake light. Move to the front of the vehic
Raising The Soft Top1. Unclip and move the sun visors to the side.2. Install door frames, if removed. Refer to “Door Frame”in this section for further
5. Make sure the Sunrider威 bracket on the side bowslatches to the door rails (Sunrider威 Models only).6. Open the header latches and engage the hook on
7. If the swing gate brackets were removed, install themby hooking the rear edge of the bracket on the interiorside of the body channel. Then, rotate
9. Partially install the sail panel retainers into the bodyside channel, leaving the last 3 in (7.6 cm) toward therear window loose (on both sides). P
11. Insert the front retainer of the window into the doorchannel, making sure the retainer is fully seated andproperly positioned on the door frame. F
12. Insert the retainer along the bottom edge of thewindow into the bottom side channel, beginning atthe front and working to the rear of the vehicle.
13. Locate the black swing gate bar. Slide the swing gatebar over the receiver at the bottom inside of the rearwindow. The spongy part of the seal sho
15. Run the zipper fully around to the right side of thewindow.16. Grasp the swing gate bar and position it into theswing gate brackets.3UNDERSTANDING
• For vehicles not equipped with the EVIC, the RemoteUnlock feature can be enabled or disabled by perform-ing the following steps:1. Press and hold th
17. Insert the rear window retainer into the swing gatebracket on both the left and right sides.18. Apply downward pressure on the top corner of there
SOFT TOP — FOUR-DOOR MODELSPlease visit the owner’s section of Jeep.com for instruc-tional videos.CAUTION!The soft top is not designed to carry any ad
CAUTION! (Continued)• Do not lower the top with the windows installed.Window and top damage may occur.• Refer to “Appearance Care for Fabric Top Model
CAUTION!Failure to follow these cautions may cause interiorwater damage, stains or mildew on the top material:• It is recommended that the top be free
Quick Steps For Lowering The Soft Top1. Remove the side windows.2. Remove the back window.NOTE: Start zipper from the right side to remove backwindow.
3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body sidechannel at the rear corners of the vehicle.
5. Fold the sail panels so that they rest on top of the softtop.6. Fold header rearward, pulling the fabric to the rear.254 UNDERSTANDING THE FEATURES
7. Release Sunrider威 latch (both sides).3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255Information Provided by:
8. Open the swing gate and lower the top.NOTE: Ensure the fabric does not overhang the sides ofthe vehicle.Quick Steps For Raising The Soft Top1. Open
2. Install rear corner panels.3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257Information Provided by:
Sound Horn On LockThis feature will cause the horn to chirp when the doorsare locked with the RKE transmitter. This feature can beturned on or turned
3. Rotate the header forward. 4. Engage the header latches.258 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Provided by:
5. Install the back window. 6. Install the side windows.3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259Information Provided by:
7. Insert the front retainer of the window into the doorchannel, making sure the retainer is fully seated andproperly positioned on the door frame. Fa
Folding Down The Soft Top1 — Header Bow 6 — Body Side Retainer2 — 2–Bow 7 — Quarter Window3 — 3–Bow 8 — Check Strap4 — 4–Bow 9 — Front Retainer — Quar
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail Panels262 UNDERSTANDING THE FEATURES OF YOUR VEHICLEInformation Pro
NOTE: Clean side and rear windows before removal toassist in preventing scratching during removal of the softtop. If zippers are difficult to operate
4. Open the swing gate.5. Before unzipping the rear window, release the first 3 in(7.6 cm) of both sail panels from the channel. Removethe swing gate
6. Remove the rear window retainer from the swing gatebracket on both the left and right sides.7. Stow the windows carefully to avoid scratching.8. Un
11. Finish releasing the sail panel retainers from the bodyside channel at the rear corners of the vehicle.NOTE: When releasing the sail panel retaine
13. The swing gate brackets do not need to be removedunless the hard top is being installed. To remove theswing gate brackets, pull the front of the b
To Turn Off Flash Lights With LockThis feature will cause the turn signal lights to flash whenthe doors are locked or unlocked with the RKE transmit-t
15. Fold back the front section of the top, pulling thefabric rearward. Gently rest the header on top of therear portion of the deck.16. Fold the top
17. Release the side bows by pressing down on the latchabove the front of the rear door. Push the toprearward to disengage. Repeat this step on the ot
19. Gently slide the side bows off the door frame trackand lower the top down into the vehicle.NOTE:Help from another person will ease this operation.
Putting Up The Soft TopNOTE: Be extremely careful when putting up the softtop to prevent the doors from getting scratched. It may behelpful to open th
5. Insert the slider feature of the knuckles into the doorframe tracks and slide the top forward.6. Ensure that the top locks into the Sunrider威 locki
7. Unclip and move the sun visors to the side.8. Standing on the side of the vehicle, lift the top by theside bow until it rests on the windshield fra
10.If the swing gate brackets were removed, install themby hooking the rear edge of the bracket on the interiorside of the body channel. Then, rotate
Partially install the sail panel retainers into the body sidechannel, leaving the last 3 in (7.6 cm) toward the rearwindow loose (on both sides). Pull
13. Insert the front retainer of the window into the doorchannel, making sure the retainer is fully seated andproperly positioned on the door frame. F
14. Insert the retainer along the bottom edge of thewindow into the bottom side channel, beginning atthe front and working to the rear of the vehicle.
Programming Additional TransmittersRefer to Sentry Key威 “Customer Key Programming.”If you do not have a programmed RKE transmitter,contact your author
15. Locate the black swing gate bar. Slide the swing gatebar over the receiver at the bottom inside of the rearwindow. The spongy part of the seal sho
17. Run the first zipper fully around to the right side ofthe window.18. Grasp the swing gate bar and position it into theswing gate brackets.19. Inse
20. Complete the installation of the sail panel by insert-ing the rest of the retainer into the body channel.21. Close the header latches and return t
Opening The Sunrider姞1. Unclip and move the sun visors to the side.2. Release the header latches from the loops on thewindshield frame.3. Slide the pl
4. Grasp the header and lift the top back. Make sure thematerial is folded back as shown.NOTE: The Sunrider威 latch on the door rail should notbe activ
Closing The Sunrider姞1. Remove the straps from the side bows.2. Unclip and move the sun visors to the side.3. Grasp the front header and pull it to th
Opening The Sunrider姞1. Unclip and move the sun visors to the side.2. Release the header latches from the loops on thewindshield frame.3. Grasp the fr
4. Fold back the front section of the top and gently restthe header on top of the rear portion of the deck.5. Fold the top so that the material forms
6. Secure the top by using the two provided straps. Eachstrap will wrap around the side bow and Velcro威 toitself; use one strap on each side of the ve
Raise the windshield and reinstall the side bars as soon asthe task that required their removal is completed andbefore you return to on-road driving.
Transmitter Battery ReplacementThe recommended replacement battery is CR2032.NOTE: Perchlorate Material – special handling may ap-ply. See www.dtsc.ca
Lowering The Windshield And Removing SideBars1. Lower the fabric top or remove the hard top followingthe instructions in this manual.NOTE: To assist i
7. Remove the one hex bolt (13 mm) visible through theplastic trim on the bottom side of the side bar, one hexbolt (13 mm) on the side of the side bar
WARNING!You or others could be injured if you carry the sidebars loose in your vehicle. Remove the side bars fromthe vehicle or securely store them as
12. Lower the windshield gently until it contacts therubber hood bumpers.13. Secure the windshield by passing a cinch strapthrough the footman hoop on
3. Attach the front of the side bar to the windshieldframe.• Install the top two hex bolts (13 mm) first, then thelower side hex bolt (13 mm). The low
REAR WINDOW FEATURES — HARD TOP ONLYRear Window Wiper/Washer — If EquippedA rotary switch on the center portion of the control lever(located on the ri
Rear Window Defroster — If EquippedThe rear window defroster button is located onthe bottom right-side of the blower control knob.Press this button to
UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 INSTRUMENT PANEL FEATURES ...298䡵 INSTRUMENT CLUSTER ...299䡵 INSTRUMENT CLUSTER DESC
▫ System Status ...331▫ Personal Settings (Customer-ProgrammableFeatures) ...331䡵 MEDIA CENTER 230 (REQ)
▫ Operating Instructions — Radio Mode...365▫ Operation Instructions — CD MODE forCD and MP3 Audio Play ...371▫ Notes On Playing MP3 F
TABLE OF CONTENTSSECTION PAGE1INTRODUCTION ...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
REMOTE STARTING SYSTEM — IF EQUIPPEDThis system uses the Remote Keyless Entry(RKE) transmitter to start the engine conve-niently from outside the vehi
INSTRUMENT PANEL FEATURES1 — Air Outlet 7 — Climate Controls2 — Instrument Cluster 8 — Power Outlet3 — Radio 9 — Lower Switch Bank4 — Assist Handle 10
INSTRUMENT CLUSTER4UNDERSTANDING YOUR INSTRUMENT PANEL 299Information Provided by:
INSTRUMENT CLUSTER DESCRIPTIONS1. Fuel GaugeThe pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON/RUN position.2.
7. Seat Belt Reminder LightWhen the ignition switch is first turned to ON/RUN, this light will turn on for four to eightseconds as a bulb check. Durin
11. Brake Warning LightThis light monitors various brake functions,including brake fluid level and parking brakeapplication. If the brake light turns
WARNING! (Continued)It will take longer to stop the vehicle. You could havea collision. Have the vehicle checked immediately.Vehicles equipped with th
13. Air Bag Warning LightThis light will turn on for four to eight secondsas a bulb check when the ignition switch is firstturned to ON/RUN. If the li
gauge to pass ⬙H.⬙ In this case, a continuous chime willsound, until the engine is allowed to cool or the 4 minutesduration is expired, whichever come
WARNING! (Continued)look under the hood yourself, see “Maintaining YourVehicle”. Follow the warnings under the CoolingSystem Pressure Cap paragraph.19
the vehicle manufacturer on the vehicle placard or tireinflation pressure label. (If your vehicle has tires of adifferent size than the size indicated
WARNING! (Continued)• Keep Remote Keyless Entry (RKE) transmittersaway from children. Operation of the Remote StartSystem, windows, door locks or othe
TPMS from functioning properly. Always check theTPMS malfunction telltale after replacing one or moretires or wheels on your vehicle, to ensure that t
Vehicle Odometer MessagesWhen the appropriate conditions exist, the followingodometer messages will display:ECO ...Fuel Saver Indica
(e.g., snow plowing, off-road operation). If this “HOT-OIL” message turns on, stop the vehicle and run theengine at idle or faster with the transmissi
CHAngE OIL MessageYour vehicle is equipped with an engine oil changeindicator system. The “CHANgE OIL” message will flashin the instrument cluster odo
Certain conditions, such as a loose or missing gas cap,poor quality fuel, etc., may illuminate the light afterengine start. The vehicle should be serv
engine running. If the “ESC Activation/Malfunction In-dicator Light” comes on continuously with the enginerunning, a malfunction has been detected in
27. Sway Bar Indicator Light — If EquippedThis indicator will illuminate when the frontsway bar is disconnected.28. Electronic Stability Control (ESC)
30.Electronic Vehicle Information Center (EVIC) Display/Compass Mini-Trip Computer Display — If EquippedWhen the appropriate conditions exist, this di
Control ButtonsThe Compass/Temperature control buttons are locatedon the left spoke of the steering wheel.Press and release the STEP button on the ste
Compass/Temperature DisplayNOTE: If the vehicle is equipped with a ChryslerUconnect™ gps (Navigation Radio), the NAV system willprovide the compass di
• The engine can be started two consecutive times (two15-minute cycles) with the RKE transmitter. However,the ignition switch must be cycled to the ON
To change the zone, press and release the STEP button toincrease the variance one step. Repeat as necessary untilthe desired variance is achieved.NOTE
NOTE:•A good calibration requires a level surface and an envi-ronment free from large metallic objects such as build-ings, bridges, underground cables
Trip ConditionsTrip Odometer (ODO) / ECO(Fuel Saver Indicator) — If EquippedThis display shows the distance traveled since the lastreset. Press and re
Trip AShows the total distance traveled for trip A since the lastreset.Trip BShows the total distance traveled for trip B since the lastreset.ECO (Fue
This system conveniently allows the driver to select avariety of useful information by pressing the switchesmounted on the steering wheel. The EVIC co
MENU ButtonPress and release the MENU button to advancethe display to each of the EVIC Main Menufeatures or to return to the Main Menu from asub-menu.
Electronic Vehicle Information Center (EVIC)DisplaysWhen the appropriate conditions exist, the EVIC displaysthe following messages:• Low Tire Pressure
• Check Gascap (refer to “Adding Fuel” in “StartingAnd Operating” for more details)• Oil Change Required (with a single chime)• ECO (Fuel Saver Indica
EVIC Main MenuTo step to each main menu feature press and release theMENU button once for each step. A step from the lastitem in the list will cause t
NOTE: The system will display the last known outsidetemperature when starting the vehicle and may need tobe driven several minutes before the updated
DOORSCAUTION!Careless handling and storage of the removable doorpanels may damage the seals, causing water to leakinto the vehicle’s interior.Upper Ha
Manual Compass CalibrationIf the compass appears erratic and the “CAL” indicatordoes not appear in the EVIC display, you must put thecompass into the
To Change The Compass Variance:1. Turn the ignition switch RUN (it is not necessary tostart the engine).2.Press the MENU button until Personal Setting
Distance To Empty (DTE)Shows the estimated distance that can be traveled withthe fuel remaining in the tank. This estimated distance isdetermined by a
System StatusDisplays SYSTEM OK if there are no active WarningMessages stored. Pressing and releasing the DOWNbutton when SYSTEM OK is displayed will
Auto Unlk On ExitWhen ON is selected, all doors will unlock when thevehicle is stopped and the transmission is in the PARK orNEUTRAL position and the
when exiting the vehicle. To make your selection, pressand release the SELECT button until “0,” “30,” “60,” or“90” appears.Headlamps with Wipers (Avai
Hill Start Assist (HSA) — If EquippedWhen on is selected, the HSA system is active. Refer to“Electronic Brake Control System” in “Starting AndOperatin
MEDIA CENTER 230 (REQ) — AM/FM STEREORADIO AND 6–DISC CD/DVD CHANGER(MP3/WMA AUX JACK)NOTE: The radio sales code is located on the lower rightside of
SEEK ButtonsPress and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left s
TIME ButtonPress the TIME button to alternate locations of the timeand frequency display.Clock Setting Procedure1. Press and hold the TIME button unti
Front Door RemovalWARNING!Do not drive your vehicle on public roads with thedoors removed as you will lose the protection thatthey can provide. This p
Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef
Toggle the MUSIC TYPE button to select the followingformat types:Program Type16-Digit CharacterDisplayNo program type orundefinedNoneAdult Hits Adlt H
By pressing the SEEK button when the Music Type icon isdisplayed, the radio will be tuned to the next frequencystation with the same selected Music Ty
NOTE:• The available selections for each of the above entriesvaries depending upon the disc.• These selections can only be made while playing aDVD.• V
Audio Language — If EquippedSelecting this item allows you to choose a default audiolanguage (effective only if the language is supported bythe disc).
a disc is loaded, changes will not be effective. Also, thedefaults are effective only if the disc supports thecustomer-preferred settings.AM and FM Bu
Operation Instructions - (DISC MODE for CD andMP3/WMA Audio Play, DVD-VIDEO)The radio DVD player and many DVD discs are coded bygeographic region. The
Eject Button — Ejecting Compact Disc(s)Press the EJECT button and the pushbuttonwith the corresponding number (1-6) where theCD was loaded and the dis
Notes On Playing MP3/WMA FilesThe radio can play MP3/WMA files; however, acceptableMP3/WMA file recording media and formats are limited.When writing M
If a disc contains multi-formats, such as CD audio andMP3/WMA tracks, the radio will only play the MP3/WMA tracks on that disc.Supported MP3/WMA File
tab, allowing the tab to be pressed down and enabling theharness to be disconnected.4. Unhook the door strap from the body hook. Be carefulnot to allo
ID3 Tag information for artist, song title, and album titleare supported for ID3 version 1 tags. ID3 version 2 is notsupported by the radios.Playlist
INFO Button (DISC Mode for MP3/WMA Play)Pressing the INFO button repeatedly will scroll throughthe following TAG information: Song Title, Artist, File
TIME Button (Auxiliary Mode)Press the TIME button to change the display fromelapsed playing time to time of day. The time of day willdisplay for five
DTS™“DTS™ and “DTS™ 2.0” are trademarks of DigitalTheater Systems, Inc.Uconnect™ Multimedia (Satellite Radio) —If EquippedSatellite radio uses direct
To access the ESN/SID, refer to the following steps:ESN/SID AccessWith the ignition switch in the ON/RUN or ACC posi-tion and the radio on, press the
Operating Instructions - Uconnect™ Multimedia(Satellite) ModeNOTE: The ignition switch must be in the ON/RUN orACC position to operate the radio.SEEK
MUSIC TYPE ButtonPressing this button once will turn on the Music Typemode for five seconds. Pressing the MUSIC TYPE buttonor turning the TUNE/SCROLL
You may add a second channel to each pushbutton byrepeating the above procedure with this exception: Pressthe SET button twice and SET 2 will show in
MEDIA CENTER 130 (SALES CODE RES)NOTE: The radio sales code is located on the lower rightside of the radio faceplate.Operating Instructions — Radio Mo
SEEK ButtonsPress and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left s
Rear Door Removal (Four-Door Models)WARNING!Do not drive your vehicle on public roads with thedoors removed as you will lose the protection thatthey c
Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef
You may add a second station to each pushbutton byrepeating the above procedure with this exception: Pressthe SET/RND button twice and SET 2 will show
If you insert a disc with the ignition ON/RUN and theradio ON, the unit will switch from radio to CD modeand begin to play when you insert the disc. T
the current selection. Pressing and holding the SEEKbutton will allow faster scrolling through the tracks inCD and MP3 modes.TIME ButtonPress this but
Notes on Playing MP3 FilesThe radio can play MP3 files; however, acceptable MP3file recording media and formats are limited. Whenwriting MP3 files, pa
Multisession disc formats are supported by the radio.Multisession discs may contain combinations of normalCD audio tracks and computer files (includin
Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f
MEDIA CENTER 130 WITH SATELLITE RADIO(SALES CODE RES+RSC)NOTE: The radio sales code is located on the lower rightside of the radio faceplate.Operating
SEEK ButtonsPress and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left s
Clock Setting Procedure1. Press and hold the TIME button until the hours blink.2. Adjust the hours by turning the right side TUNE/SCROLL control knob.
5. Unplug the wiring harness connector.NOTE: If the red latch on the connector is locked, pushthe red latch to the right until you can only see the la
Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef
Toggle the MUSIC TYPE button to select the followingformat types:Program Type16-Digit CharacterDisplayNo program type orundefinedNoneAdult Hits Adlt H
By pressing the SEEK button when the Music Type icon isdisplayed, the radio will be tuned to the next frequencystation with the same selected Music Ty
You may add a second station to each pushbutton byrepeating the above procedure with this exception: Pressthe SET/RND button twice and SET 2 will show
If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The d
previous selection if the CD is within the first second ofthe current selection. Pressing and holding the SEEKbutton will allow faster scrolling throu
Notes On Playing MP3 FilesThe radio can play MP3 files; however, acceptable MP3file recording media and formats are limited. Whenwriting MP3 files, pa
Multisession disc formats are supported by the radio.Multisession discs may contain combinations of normalCD audio tracks and computer files (includin
Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f
Press and hold the INFO button again for three secondsto return to ⬙elapsed time⬙ display.Operation Instructions - Auxiliary ModeThe auxiliary (AUX) j
NOTE: Doors are heavy; use caution when removingthem.To reinstall the door(s), perform the previous steps in theopposite order.DOOR LOCKSManual Door L
how to setup your on-line listening account. For furtherinformation, call the toll-free number 888-539-7474,or visit the Sirius web site at www.sirius
Reception QualitySatellite reception may be interrupted due to one of thefollowing reasons:• The vehicle is parked in an underground parkingstructure
additional three seconds will make the radio display theSong Title all of the time (press and hold again to returnto normal display).RW/FFPressing the
SET Button – To Set the Pushbutton MemoryWhen you are receiving a channel that you wish tocommit to pushbutton memory, press the SET button.The symbol
iPod姞/USB/MP3 CONTROL — IF EQUIPPEDNOTE: This section is for sales code RES and REQ/REL/RET radios only with Uconnect™. For sales codeRBZ/RHB, RHR, RH
Once the audio device is connected and synchronized tothe vehicle’s iPod威/USB/MP3 control system (iPod威 orexternal USB device may take a few minutes t
Controlling The iPod姞 Or External USB DeviceUsing Radio ButtonsTo get into the iPod威/USB/MP3 control mode and accessa connected audio device, either p
• Use the << SEEK and SEEK>> buttons to jump to theprevious or next track. Pressing the SEEK>> buttonduring play mode will jump to t
List Or Browse ModeDuring Play mode, pressing any of the buttons describedbelow, will bring up List mode. List mode enablesscrolling through the list
• To exit List mode without selecting a track, press thesame PRESET button again to go back to Play mode.• LIST button: The LIST button will display t
NOTE: The ignition key that is used to start the vehicleis used to lock or unlock the doors, swing gate, glovecompartment, and console storage.WARNING
Bluetooth Streaming Audio (BTSA)Music can be streamed from your cellular phone to theUconnect™ phone system.Controlling BTSA Using Radio ButtonsTo get
STEERING WHEEL AUDIO CONTROLSThe remote sound system controls are located on the rearsurface of the steering wheel. Reach behind the wheel toaccess th
Radio OperationPressing the top of the switch will “Seek” up for the nextlistenable station and pressing the bottom of the switchwill “Seek” down for
4. Do not use solvents such as benzene, thinner, cleaners,or anti-static sprays.5. Store the disc in its case after playing.6. Do not expose the disc
Manual Heating And Air ConditioningThe Manual Temperature Controls consist of a series ofouter rotary dials and inner push knobs.Blower ControlRotate
Temperature ControlRotate this control to regulate the tem-perature of the air inside the passengercompartment. Rotating the dial leftinto the blue ar
Bi-LevelAir is directed through the panel and floor outlets.NOTE: For all settings, except full cold or full hot, thereis a difference in temperature
NOTE:• Continuous use of the Recirculation mode may makethe inside air stuffy and window fogging may occur.Extended use of this mode is not recommende
Automatic Temperature Control (ATC) —If EquippedAutomatic OperationThe Automatic Temperature Control system automati-cally maintains the climate in th
The recommended setting for maximum comfort is 72°F(22°C) for the average person; however, this may vary.NOTE:• The temperature setting can be adjuste
Information Provided by:
Power Door Locks — If EquippedThe power door lock switch is located on each front doorpanel. Press the switch forward to lock the doors, andrearward t
398 UNDERSTANDING YOUR INSTRUMENT PANELInformation Provided by:
The operator can override the AUTO mode setting tochange airflow distribution by rotating the Mode Controlknob (on the right) to one of the following
• Air Conditioner ControlPress this button to turn on the airconditioning during manual operationonly. When the air conditioning isturned on, cool deh
• Most of the time, when in Automatic Operation, youcan temporarily put the system into Recirculationmode by pressing the Recirculation button. Howeve
Window FoggingInterior fogging on the windshield can be quickly re-moved by turning the mode selector to Defrost. TheDefrost/Floor mode can be used to
Control Setting Suggestions For Various Weather Conditions4UNDERSTANDING YOUR INSTRUMENT PANEL 403Information Provided by:
Information Provided by:
STARTING AND OPERATINGCONTENTS䡵 STARTING PROCEDURES ...410▫ Manual Transmission – If Equipped ...410▫ Automatic Transmission – If Eq
䡵 FOUR–WHEEL DRIVE OPERATION(COMMAND-TRAC I威 OR ROCK-TRAC威) . . . .428▫ Operating Instructions/Precautions ...428▫ Shift Positions ...
▫ Traction Control System (TCS) ...457▫ Brake Assist System (BAS) ...457▫ Hill Start Assist (HSA) ...458▫ Electroni
Automatic Door Locks — If EquippedWhen enabled, the door locks will lock automaticallywhen the vehicle’s speed exceeds 15 mph (24 km/h). Theauto door
▫ Limited-Use Spare – If Equipped ...488▫ Tire Spinning ...489▫ Tread Wear Indicators ...490▫ Life Of Tire
䡵 TRAILER TOWING ...515▫ Common Towing Definitions ...515▫ Trailer Hitch Classification ...518▫ Trailer Towing
STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts.WARNING!• When le
Normal StartingNOTE: Normal starting of either a cold or a warmengine is obtained without pumping or pressing theaccelerator pedal.Turn the ignition s
WARNING! (Continued)• If the vehicle has a discharged battery, boostercables may be used to obtain a start from a boosterbattery or the battery in ano
With Tip Start – Automatic Transmission OnlyIf the engine fails to start after you have followed the“Normal Starting” or “Extreme Cold Weather” proce-
MANUAL TRANSMISSION — IF EQUIPPEDWARNING!You or others could be injured if you leave thevehicle unattended without having the parkingbrake fully appli
ShiftingFully press the clutch pedal before shifting gears. As yourelease the clutch pedal, lightly press the acceleratorpedal.You should always use f
DownshiftingMoving from a high gear down to a lower gear isrecommended to preserve brakes when driving downsteep hills. In addition, downshifting at t
Manual Transmission Downshift Speeds inMPH (KM/H)GearSelec-tion6to5 5to4 4to3 3to2 2to1Maxi-mumSpeed80(129)70(113)50(81)30(48)15(24)NOTE: Vehicle spee
Child-Protection Door Lock System — RearDoorsTo provide a safer environment for small children ridingin the rear seats, the rear doors are equipped wi
AUTOMATIC TRANSMISSION — IF EQUIPPEDCAUTION!Damage to the transmission may occur if the follow-ing precautions are not observed:• Shift into PARK only
WARNING! (Continued)number of reasons. A child or others could beseriously or fatally injured. Children should bewarned not to touch the parking brake
Five-Speed Automatic TransmissionThe shift lever position display (located in the instrumentcluster) indicates the transmission gear range. You mustpr
Gear RangesDO NOT race the engine when shifting from PARK orNEUTRAL into another gear range.NOTE: After selecting any gear range, wait a moment toallo
WARNING!• Never use the PARK position as a substitute for theparking brake. Always apply the parking brakefully when parked to guard against vehicle m
WARNING! (Continued)reasons. A child or others could be seriously orfatally injured. Children should be warned not totouch the parking brake, brake pe
NEUTRALUse this range when the vehicle is standing for prolongedperiods with the engine running. The engine may bestarted in this range. Apply the par
When frequent transmission shifting occurs (such aswhen operating the vehicle under heavy loading condi-tions, in hilly terrain, traveling into strong
5. Restart the engine.6. Shift into the desired gear range. If the problem is nolonger detected, the transmission will return to normaloperation.NOTE:
WARNING!Do not downshift for additional engine braking on aslippery surface. The drive wheels could lose theirgrip and the vehicle could skid, causing
NOTE: For emergency exit with the system engaged,move the rocker lever rearward (unlocked position), rolldown the window and open the door with the ou
FOUR–WHEEL DRIVE OPERATION(COMMAND-TRAC I姞 OR ROCK-TRAC姞)WARNING!Failure to engage a position completely can causetransfer case damage or loss of powe
In the event that additional traction is required, thetransfer case 4H and 4L positions can be used to lock thefront and rear driveshafts together, fo
WARNING!You or others could be injured if you leave the vehicleunattended with the transfer case in the N (Neutral)position without first fully engagi
speed. This range (4L) provides additional traction andmaximum pulling power for loose, slippery road surfacesonly. Do not exceed 25 mph (40 km/h).The
WARNING!Failure to engage a position completely can causetransfer case damage or loss of power and vehiclecontrol. You could have a collision. Do not
AXLE LOCK (TRU–LOK姞) — RUBICON MODELSThe AXLE LOCK switch is located on the instrumentpanel (to the left of the steering column).This feature will onl
ELECTRONIC SWAY BAR DISCONNECT —IF EQUIPPEDYour vehicle may be equipped with an electronic discon-necting stabilizer/sway bar. This system allows grea
sway bar should remain in on-road mode during normaldriving conditions.WARNING!Do not disconnect the stabilizer bar and drive onhard-surfaced roads or
To return to on-road mode, press the SWAY BAR switchagain.WARNING!If the stabilizer/sway bar will not return to on-roadmode, vehicle stability is grea
OFF-ROAD DRIVING TIPSSide Step Removal – If EquippedNOTE: Prior to off-road usage, the side steps should beremoved to prevent damage.1. Remove the two
Four-Door ModelsThe lower left switch controls the left rear passengerwindow, and the lower right switch controls the rightrear passenger window.Auto-
The Basics Of Off-Road DrivingYou will encounter many types of terrain driving off-road. You should be familiar with the terrain and areabefore procee
extreme situations such as deep snow, mud, steep in-clines, or sand where additional low speed pulling poweris needed. Vehicle speeds in excess of 25
MudDeep mud creates a great deal of suction around the tiresand is very difficult to get through. You should usesecond gear (manual transmission), or
Crossing Obstacles (Rocks And Other HighPoints)While driving off-road, you will encounter many types ofterrain. These varying types of terrain bring d
CAUTION!• Never attempt to straddle a rock that is largeenough to strike your axles or undercarriage.• Never attempt to drive over a rock which is lar
CAUTION!Do not attempt to cross a log with a greater diameterthan the running ground clearance or the vehicle willbecome high-centered.Getting High-Ce
Before Climbing A Steep HillAs you approach a hill, consider its grade or steepness.Determine if it is too steep. Look to see what the tractionis on t
Driving DownhillBefore driving down a steep hill, you need to determineif it is too steep for a safe descent. What is the surfacetraction? Is the grad
If You Stall Or Begin To Lose HeadwayIf you stall or begin to lose headway while climbing asteep hill, allow your vehicle to come to a stop andimmedia
accelerate through the crossing. After crossing any waterhigher than the bottom of the axle differentials, youshould inspect all of the vehicle fluids
Rear Power Windows — Four-Door ModelsThe rear passenger window switches are located on theback of the center floor console. Press the switch down-ward
Crossing Puddles, Pools, Flooded Areas Or OtherStanding WaterPuddles, pools, flooded or other standing water areasnormally contain murky or muddy wate
WARNING!Never drive through fast moving deep water. It canpush your vehicle downstream, sweeping it out ofcontrol. This could put you and your passeng
WARNING!Abrasive material in any part of the brakes may causeexcessive wear or unpredictable braking. You mightnot have full braking power when you ne
• Upon initial start-up in cold weather, the power steer-ing pump may make noise for a short amount of time.This is due to the cold, thick fluid in th
WARNING!Fluid level should be checked on a level surface andwith the engine off to prevent injury from movingparts and to ensure accurate fluid level
When the parking brake is applied with the ignitionswitch ON, the “Brake Warning Light” in the instrumentcluster will illuminate.NOTE:• When the parki
WARNING! (Continued)• Never leave children alone in a vehicle, or withaccess to an unlocked vehicle. Allowing children tobe in a vehicle unattended is
ANTI-LOCK BRAKE SYSTEMThe Anti-Lock Brake System (ABS) is designed to aid thedriver in maintaining vehicle control under adversebraking conditions. Th
WARNING! (Continued)• The Anti-Lock Brake System (ABS) cannot preventthe natural laws of physics from acting on thevehicle, nor can they increase brak
WARNING!The Anti-Lock Brake System (ABS) cannot preventthe natural laws of physics from acting on the ve-hicle, nor can they increase the traction aff
REAR SWING GATEThe rear swing gate can be unlocked by using the key,Remote Keyless Entry (RKE) transmitter, or by activatingthe power door lock switch
benefit of the system, you must apply continuous brak-ing pressure during the stopping sequence. Do notreduce brake pedal pressure unless braking is n
WARNING! (Continued)another vehicle or object. To avoid this, do not applythrottle while pressing the clutch pedal until you areready to release the c
HSA On Automatic Transmission VehiclesThe system will work in REVERSE, and all forward gearson vehicles equipped with an automatic transmission.The sy
WARNING! (Continued)• HSA is not a parking brake. Always apply theparking brake fully when leaving your vehicle.Also, be certain to leave the transmis
6. Cycle ignition switch OFF then ON.7. If the sequence was completed properly, the “ESCActivation/Malfunction Indicator Light” will blinkseveral time
WARNING! (Continued)capabilities of an ERM-equipped vehicle must neverbe exploited in a reckless or dangerous mannerwhich could jeopardize the user’s
WARNING!Electronic Stability Control (ESC) cannot prevent thenatural laws of physics from acting on the vehicle,nor can it increase the traction affor
When in ⬙Partial Off⬙ mode, the TCS portion of ESC hasbeen disabled and the “ESC Activation/MalfunctionIndicator Light” will be illuminated.All other
ESC OFF switch. This will restore normal “ESC On”mode of operation.WARNING!With the ESC switched off, the enhanced vehiclestability offered by ESC and
WARNING!With the ESC switched off, the enhanced vehiclestability offered by ESC and ERM are unavailable.In an emergency evasive maneuver, the ESC andE
OCCUPANT RESTRAINTSSome of the most important safety features in yourvehicle are the restraint systems:• Three-point lap and shoulder belts for the dr
ESC Activation/Malfunction Indicator Light AndESC OFF Indicator LightThe “ESC Activation/Malfunction IndicatorLight” in the instrument cluster will co
The “ESC OFF Indicator Light” indicates theElectronic Stability Control (ESC) is off.Trailer Sway Control (TSC)TSC uses sensors in the vehicle to reco
Hill Descent Control (HDC) – If EquippedHDC is only intended for low speed off-road driving.HDC maintains vehicle speed while descending hills inoff-r
Enabling HDC1. Shift the transfer case into 4WD LOW range. Refer to“Four-Wheel Drive Operation” in “Starting and Oper-ating” for further information.2
NOTE:• P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the s
Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro
EXAMPLE:Service Description:95 = Load Index— A numerical code associated with the maximum load a tire can carryH = Speed Symbol— A symbol indicating t
Tire Identification Number (TIN)The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white
Tire Terminology And DefinitionsTerm DefinitionB-Pillar The vehicle B-Pillar is the structural member of the body locatedbehind the front door.Cold Ti
Tire Loading And Tire PressureTire Placard LocationTire Placard Location (Two-Door Model)Tire Placard Location (Four-Door Model)5STARTING AND OPERATIN
NOTE: The Advanced Front Air Bags have a multistageinflator design. This allows the air bag to have differentrates of inflation based on several facto
Tire And Loading Information PlacardThis placard tells you important information about the:1) number of people that can be carried in the vehicle2) to
To determine the maximum loading conditions of yourvehicle, locate the statement “The combined weight ofoccupants and cargo should never exceed XXX lb
NOTE:• The following table shows examples on how to calcu-late total load, cargo/luggage, and towing capacitiesof your vehicle with varying seating co
5STARTING AND OPERATING 481Information Provided by:
WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti
WARNING! (Continued)• Unequal tire pressures from one side of the vehicleto the other can cause the vehicle to drift to theright or left.• Always driv
CAUTION!After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the va
Tire Pressures For High Speed OperationThe manufacturer advocates driving at safe speedswithin posted speed limits. Where speed limits or condi-tions
the tire sidewall. Use all season tires only in sets of four;failure to do so may adversely affect the safety andhandling of your vehicle.Summer Or Th
Spare Tire Matching Original Equipped Tire AndWheel – If EquippedYour vehicle may be equipped with a spare tire andwheel equivalent in look and functi
You should read the instructions provided with yourchild restraint to make sure that you are using it properly.2. All occupants should always wear the
Since this tire has limited tread life the original equip-ment tire should be repaired (or replaced) and reinstalledon your vehicle at the first oppor
your original equipment tire, replace (or repair) theoriginal equipment tire and reinstall on the vehicle at thefirst opportunity.WARNING!Limited-use
Tread Wear IndicatorsTread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced.These indic
WARNING!Tires and the spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sud
WARNING!•Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations ofunapproved tires and wheels may change
• P225/75R16 or a P235/65R17 tire with the use of atraction device that meets the SAE type “Class S”specification is recommended.WARNING!Using tires o
TIRE ROTATION RECOMMENDATIONSThe tires on the front and rear of your vehicle operate atdifferent loads and perform different steering, handling,and br
CAUTION!Proper operation of four-wheel drive vehicles de-pends on tires of equal size, type and circumferenceon each wheel. Any difference in tire siz
must be increased to the recommended cold placardpressure in order for the “Tire Pressure MonitoringTelltale Light” to be turned OFF. The system will
CAUTION! (Continued)• After inspecting or adjusting the tire pressure,always reinstall the valve stem cap. This willprevent moisture and dirt from ent
INTRODUCTIONCONTENTS䡵 INTRODUCTION ...4䡵 ROLLOVER WARNING ...5䡵 HOW TO USE THIS MANUAL ...6䡵 WARNINGS
WARNING! (Continued)• In a collision, you and your passengers can suffermuch greater injuries if you are not properly buck-led up. You can strike the
Premium and Base TPM SystemThe Tire Pressure Monitor System (TPMS) uses wirelesstechnology with wheel rim-mounted electronic sensors tomonitor tire pr
received. The vehicle may need to be driven for up to20 minutes above 15 mph (24 km/h) to receive thisinformation.The “Tire Pressure Monitoring Tellta
3. Lots of snow or ice around the wheels or wheelhousings.4. Using tire chains on the vehicle.5. Using wheels/tires not equipped with TPM sensors.NOTE
below the low-pressure warning limit in any of thefour active road tires. The vehicle may need to bedriven for up to 20 minutes above 15 mph (24 km/h)
Tire Pressure Monitoring Low Pressure WarningsThe Tire Pressure Monitoring Telltale Light willilluminate in the instrument cluster, and an au-dible ch
The system will automatically update, the graphic dis-play of the pressure value(s) will stop “flashing,” and theTire Pressure Monitoring Telltale Lig
If the ignition switch is cycled, this sequence will repeat,providing the system fault still exists. If the system faultno longer exists, the “Tire Pr
message to appear in the EVIC, and the graphic displaywill still show the low tire pressure value “flashing.”Driving the vehicle for up to 20 minutes
General InformationThis device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•
Over 40 auto manufacturers worldwide have issued andendorsed consistent gasoline specifications (the World-wide Fuel Charter, WWFC) which define fuel
WARNING!• It is dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding inthese areas are more likely to be se
E-85 Usage In Non-Flex Fuel VehiclesNon-FFV vehicles are compatible with gasoline contain-ing 10% ethanol (E10). Gasoline with higher ethanolcontent m
can be used at levels higher than those allowed in theUnited States. MMT is prohibited in Federal and Califor-nia reformulated gasoline.Materials Adde
Carbon Monoxide WarningsWARNING!Carbon monoxide (CO) in exhaust gases is deadly.Follow the precautions below to prevent carbonmonoxide poisoning:• Do
CAUTION!• Damage to the fuel system or emission controlsystem could result from using an improper fuel(Continued)CAUTION! (Continued)cap (gas cap). A
WARNING! (Continued)• A fire may result if gasoline is pumped into aportable container that is inside of a vehicle. Youcould be burned. Always place g
VEHICLE LOADINGCertification LabelAs required by National Highway Traffic Safety Admin-istration regulations, your vehicle has a certification labelaf
Tire SizeThe tire size on the Vehicle Certification Label representsthe actual tire size on your vehicle. Replacement tiresmust be equal to the load c
items down low and be sure that the weight is distributedequally. Stow all loose items securely before driving.Improper weight distributions can have
exceed the GVWR. Refer to “Vehicle Loading/VehicleCertification Label” in “Starting and Operating” forfurther information.Gross Trailer Weight (GTW)Th
Frontal AreaThe frontal area is the maximum height multiplied by themaximum width of the front of a trailer.Trailer Sway Control – If EquippedThe trai
Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is above the
WARNING!• An improperly adjusted Weight Distributing Hitchsystem may reduce handling, stability, brakingperformance, and could result in a collision.•
Trailer Towing Weights (Maximum Trailer Weight Ratings)The following chart provides the maximum trailer weight ratings towable for your given drivetra
Engine/TransmissionAxle ModelGCWR(GrossCombinedWt. Rating)Frontal AreaMax. GTW(GrossTrailer Wt.)Max. TrailerTongue Wt.(See Note)3.6L/Manual 3.21 Two–D
Engine/TransmissionAxle ModelGCWR(GrossCombinedWt. Rating)Frontal AreaMax. GTW(GrossTrailer Wt.)Max. TrailerTongue Wt.(See Note)3.6L/Automatic4.10 Two
Engine/TransmissionAxle ModelGCWR(GrossCombinedWt. Rating)Frontal AreaMax. GTW(GrossTrailer Wt.)Max. TrailerTongue Wt.(See Note)3.6L/Manual 3.21 Four–
Engine/TransmissionAxle ModelGCWR(GrossCombinedWt. Rating)Frontal AreaMax. GTW(GrossTrailer Wt.)Max. TrailerTongue Wt.(See Note)3.6L/Automatic4.10 Fou
Trailer And Tongue WeightAlways load a trailer with 60% to 65% of the weight inthe front of the trailer. This places 10% to 15% of theGross Trailer We
NOTE: Remember that everything put into or on thetrailer adds to the load on your vehicle. Also, additionalfactory-installed options or dealer-install
WARNING!Improper towing can lead to a collision. Follow theseguidelines to make your trailer towing as safe aspossible:• Make certain that the load is
WARNING! (Continued)• Total weight must be distributed between the towvehicle and the trailer such that the following fourratings are not exceeded:1.
3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”WARNING!•A belt that is buckled into the wrong
Towing Requirements – Trailer Brakes• Do not interconnect the hydraulic brake system orvacuum system of your vehicle with that of the trailer.This cou
Towing Requirements – Trailer Lights And WiringWhenever you pull a trailer, regardless of the trailer size,stop lights and turn signals on the trailer
Towing TipsBefore setting out on a trip, practice turning, stoppingand backing the trailer in an area away from heavytraffic.If using a manual transmi
Electronic Speed Control – If Equipped• Do not use in hilly terrain or with heavy loads.• When using the speed control, if you experience speeddrops g
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)Towing This Vehicle Behind Another VehicleTowing Condition Wheels OFF the Ground Four-Wheel Drive ModelsFl
Recreational Towing – Four-Wheel Drive ModelsNOTE: The transfer case must be shifted into NEUTRAL(N), automatic transmission must be shifted into PARK
Shifting Into NEUTRAL (N)Use the following procedure to prepare your vehicle forrecreational towing.WARNING!You or others could be injured if you leav
7. Shift the transmission into REVERSE.8. Release the brake pedal (and clutch pedal on manualtransmissions) for five seconds and ensure that there isn
Shifting Out of NEUTRAL (N)Use the following procedure to prepare your vehicle fornormal usage.1. Bring the vehicle to a complete stop, leaving it con
WHAT TO DO IN EMERGENCIESCONTENTS䡵 HAZARD WARNING FLASHERS ...538䡵 IF YOUR ENGINE OVERHEATS ...538䡵 JACKING AND TIRE CHANGING ...
WARNING! (Continued)• A shoulder belt placed behind you will not protectyou from injury during a collision. You are morelikely to hit your head in a c
HAZARD WARNING FLASHERSThe Hazard Warning flasher switch is located on theinstrument panel below the climate controls.Press the switch to turn on the
CAUTION!Driving with a hot cooling system could damage yourvehicle. If the temperature gauge reads HOT (H), pullover and stop the vehicle. Idle the ve
JACKING AND TIRE CHANGINGWARNING!• Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough offthe road to a
Jack LocationThe jack and lug wrench are located in the rear storagecompartment.NOTE: Turn the black plastic wing nut counter clock-wise to loosen the
Spare Tire StowageTo remove the spare tire from the carrier, remove the tirecover, if equipped, and remove the lug nuts with the lugwrench turning the
Jacking InstructionsWARNING!Carefully follow these tire changing warnings tohelp prevent personal injury or damage to yourvehicle:• Always park on a f
CAUTION!Do not attempt to raise the vehicle by jacking onlocations other than those indicated in the JackingInstructions for this vehicle.1. Remove th
5. Raise the vehicle by turning the jack screw to the right.Raise the vehicle till the tire is raised from the surfaceof the road. Minimum tire lift p
7. Position the spare wheel/tire on the vehicle and installthe lug nuts with the cone-shaped end toward thewheel. Lightly tighten the lug nuts clockwi
10. Remove the jack assembly and wheel blocks.11.Secure the tire, jack, and tools in their proper locations.12. Remove blocks from wheels.WARNING!A lo
WARNING!•A lap belt worn too high can increase the risk ofinjury in a collision. The belt forces won’t be at thestrong hip and pelvic bones, but acros
JUMP-STARTING PROCEDURESIf your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery inanother vehicle o
Preparations For Jump-StartThe battery in your vehicle is located in the right rear ofthe engine compartment, behind the Power DistributionCenter.WARN
1. Set the parking brake, shift the automatic transmissioninto PARK (manual transmission in NEUTRAL) andturn the ignition to LOCK.2. Turn off the heat
3. Connect the negative end (-) of the jumper cable to thenegative (-) post of the booster battery.4. Connect the opposite end of the negative (-) jum
CAUTION!Accessories that can be plugged into the vehiclepower outlets draw power from the vehicle’s battery,even when not in use (i.e., cellular phone
Control” in “Starting And Operating” for further infor-mation. Once the vehicle has been freed, press the ⬙ESCOff⬙ switch again to restore ⬙ESC On⬙ mo
EMERGENCY TOW HOOKS — IF EQUIPPEDIf your vehicle is equipped with tow hooks, they aremounted in the front and the rear.NOTE: For off-road recovery, it
3. Using a small screwdriver or similar tool, remove theshift lever override access cover (located to the right ofthe shift lever).4. Turn the ignitio
TOWING A DISABLED VEHICLEThis section describes procedures for towing a disabledvehicle using a commercial wrecker service. If the trans-mission and d
Proper towing or lifting equipment is required to preventdamage to your vehicle. Use only tow bars and otherequipment designed for this purpose, follo
Rear Center Lap/Shoulder Belt RetractorLockout — Four-Door Models OnlyThis feature is designed to lock the retractor wheneverthe 60% rear seatback is
Four–Wheel Drive ModelsThe manufacturer recommends towing with all wheelsOFF the ground. Acceptable methods are to tow thevehicle on a flatbed or with
MAINTAINING YOUR VEHICLECONTENTS䡵 ENGINE COMPARTMENT — 3.6L ...561䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .562▫ Loose Fuel Filler Cap Message ..
▫ Clutch Hydraulic System (ManualTransmission) – If Equipped ...588▫ Manual Transmission – If Equipped ...588▫ Transfer Case ...
ENGINE COMPARTMENT — 3.6L1 — Integrated Power Module (Fuses) 7 — Washer Fluid Reservoir2 — Battery 8 — Engine Coolant Reservoir3 — Engine Oil Dipstick
ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor
gas cap is properly tightened. Press the odometer resetbutton to turn the message off. If the problem persists,the message will appear the next time t
4. Approximately 15 seconds later, one of two things willhappen:• The MIL will flash for about 10 seconds and thenreturn to being fully illuminated un
available which include detailed service information foryour vehicle. Refer to these Service Manuals beforeattempting any procedure yourself.NOTE: Int
CAUTION! (Continued)• Your vehicle has been built with improved fluidsthat protect the performance and durability of yourvehicle and also allow extend
CAUTION!Overfilling or underfilling the crankcase will causeaeration or loss of oil pressure. This could damageyour engine.Change Engine OilThe oil ch
Lap/Shoulder Belt Untwisting ProcedureUse the following procedure to untwist a twisted lap/shoulder belt.1. Position the latch plate as close as possi
CAUTION!Do not use chemical flushes in your engine oil as thechemicals can damage your engine. Such damage isnot covered by the New Vehicle Limited Wa
station or governmental agency for advice on how andwhere used oil and oil filters can be safely discarded inyour area.Engine Oil FilterThe engine oil
Engine Air Cleaner Filter SelectionThe quality of replacement engine air cleaner filtersvaries considerably. Only high quality filters should beused t
CAUTION!• It is essential when replacing the cables on thebattery that the positive cable is attached to thepositive post and the negative cable is at
WARNING!• Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants
MOPAR威 Spray White Lube or equivalent to assurequiet, easy operation and to protect against rust andwear. Prior to the application of any lubricant, t
Adding Washer FluidThe fluid reservoir for the windshield washers and therear window washer (if equipped) is shared. The fluidreservoir is located in
into the passenger compartment. In addition, have theexhaust system inspected each time the vehicle is raisedfor lubrication or oil change. Replace as
Under normal operating conditions, the catalytic con-verter will not require maintenance. However, it is im-portant to keep the engine properly tuned
Cooling SystemWARNING!You or others can be badly burned by hot enginecoolant (antifreeze) or steam from your radiator. Ifyou see or hear steam coming
WARNING!Position the shoulder belt height adjusters so that thebelt rests across the middle of your shoulder. Failureto adjust the safety belt properl
Cooling System – Drain, Flush, And RefillIf the engine coolant (antifreeze) is dirty or contains aconsiderable amount of sediment, clean and flush wit
CAUTION! (Continued)• Do not use water alone or alcohol-based enginecoolant (antifreeze) products. Do not use additionalrust inhibitors or antirust pr
Please note that it is the owner’s responsibility to main-tain the proper level of protection against freezing ac-cording to the temperatures occurrin
Disposal Of Used Engine CoolantUsed ethylene glycol-based engine coolant (antifreeze) isa regulated substance requiring proper disposal. Checkwith you
If an examination of your engine compartment shows noevidence of radiator or hose leaks, the vehicle may besafely driven. The vapor will soon dissipat
Brake SystemIn order to assure brake system performance, all brakesystem components should be inspected periodically.Refer to the “Maintenance Schedul
WARNING!• Use only manufacturer’s recommended brakefluid. Refer to “Fluids, Lubricants, and GenuineParts” in “Maintaining Your Vehicle” for furtherinf
Automatic Transmission – If EquippedSelection Of LubricantIt is important to use the proper transmission fluid toensure optimum transmission performan
CAUTION!• Using a transmission fluid other than the manufac-turer’s recommended fluid may cause deteriorationin transmission shift quality and/or torq
4. Place the shift lever momentarily into each gear posi-tion (allowing time for the transmission to fully en-gage in each position), ending with the
If the passenger seating position is equipped with anALR and is being used for normal usage:Only pull the belt webbing out far enough to comfortablywr
7. Check for leaks. Release the parking brake.NOTE: To prevent dirt and water from entering thetransmission after checking or replenishing fluid, make
Fluid Level CheckCheck the fluid level by removing the fill plug. The fluidlevel should be between the bottom of the fill hole and apoint not more tha
Adding FluidFluid should be added only at filler hole until fluidbegins to run out of the hole.DrainFirst remove the fill plug (B), then the drain plu
Selection Of LubricantUse only manufacturer’s recommended fluid. Refer to“Fluids, Lubricants, and Genuine Parts” in “MaintainingYour Vehicle” for furt
Washing• Wash your vehicle regularly. Always wash your ve-hicle in the shade using MOPAR威 Car Wash or equiva-lent, or a mild car wash soap, and rinse
• If you detect any stone chips or scratches in the paint,touch them up immediately. The cost of such repairs isconsidered the responsibility of the o
Interior CareUse MOPAR威 Total Clean or equivalent to clean fabricupholstery and carpeting.Interior Trim should be cleaned starting with a dampcloth, a
When cleaning the rear view mirror, spray cleaner on thetowel or rag that you are using. Do not spray cleanerdirectly on the mirror.Cleaning Plastic I
• Do not allow any vinyl cleaner to run down and dryon the paint, leaving a streak.• After cleaning your vehicle’s fabric top, always makesure it is c
CAUTION! (Continued)• The front panel(s) must be positioned properly toensure sealing. Improper installation can causewater to leak into the vehicle’s
INTRODUCTIONCongratulations on selecting your new Chrysler GroupLLC vehicle. Be assured that it represents precisionworkmanship, distinctive styling,
How To Disengage The Automatic Locking ModeUnbuckle the combination lap/shoulder belt and allow itto retract completely to disengage the Automatic Loc
regularly. Use MOPAR威 Soft Top Zipper Cleaner andLubricant or equivalent to ease zipper operation.Before applying, make sure the zipper teeth are clea
Cavity Car-tridgeFuseMiniFuseDescriptionJ1 — —J2 30 AmpPinkTransfer CaseModuleJ3 — —J4 25 AmpNaturalDriver Door NodeJ5 25 AmpNaturalPassenger DoorNode
Cavity Car-tridgeFuseMiniFuseDescriptionJ13 60 AmpYellowIgnition Off Draw(IOD) – MainJ14 40 AmpGreenRear DefrosterJ15 40 AmpGreenFront BlowerJ17 40 Am
Cavity Car-tridgeFuseMiniFuseDescriptionM4 — —M5 25 AmpNaturalPower Inverter –If EquippedM6 20 AmpYellowPower Outlet #1/Rain SensorM7 20 AmpYellowPowe
Cavity Car-tridgeFuseMiniFuseDescriptionM12 30 AmpGreenAmplifierM13 20 AmpYellowIgnition Off Draw –Cabin CompartmentNode, Wireless Con-trol Module, SI
Cavity Car-tridgeFuseMiniFuseDescriptionM18 15 AmpBlueRight Tail/Park/Run LampM19 25 AmpNaturalAuto Shut Down(ASD #1 and #2)M20 15 AmpBlueCabin Compar
Cavity Car-tridgeFuseMiniFuseDescriptionM29 10 AmpRedPowertrainM30 15 AmpBlueWiper Motor Frt,J1962 Diagnostic FeedM31 20 AmpYellowBackup LampsM32 10 A
CAUTION!• When installing the Integrated Power Modulecover, it is important to ensure the cover is properlypositioned and fully latched. Failure to do
REPLACEMENT BULBSInterior BulbsBulb NumberAutomatic TransmissionIndicator Lamp658Heater Control Lamps (2) 194Rocker Switch Indicator Lamp(Rear Window
BULB REPLACEMENTNOTE: Lens fogging can occur under certain atmo-spheric conditions. This will usually clear as atmosphericconditions change to allow t
WARNING! (Continued)• Failure to replace the belt and retractor assemblycould increase the risk of injury in collisions.Seat Belt PretensionersThe sea
Front Park/Turn Signal1. Remove the front grille. Turn the retainers along thetop 1/4 turn counterclockwise and remove.2. Pull the bottom of the grill
Rear Tail, Stop, Turn Signal, And Backup Lamp1. Remove the two inboard screws attaching the tail lighthousing to the body. DO NOT REMOVE THEOUTER SCRE
FLUID CAPACITIESU.S. MetricFuel (Approximate) — Two Door Models 18.6 Gallons 70 LitersFuel (Approximate) — Four Door Models 22.5 Gallons 85 LitersEngi
FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant MOPAR威 Antifreeze/Coolant 10 Year/150,000 Mile For
ChassisComponent Fluid, Lubricant, or Genuine PartAutomatic Transmission –If EquippedMOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed
MAINTENANCE SCHEDULESCONTENTS䡵 MAINTENANCE SCHEDULE ...614▫ Maintenance Chart...6168MAINTENANCESCHEDULESInformation Provid
MAINTENANCE SCHEDULEYour vehicle is equipped with an automatic oil changeindicator system. The oil change indicator system willremind you that it is t
Once A Month Or Before A Long Trip:• Check engine oil level• Check windshield washer fluid level• Check the tire inflation pressures and look for unus
Maintenance ChartRefer to the Maintenance Schedules on the following pages for the required maintenance intervals.Mileage or time passed(whichever com
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
The BeltAlert威 warning sequence begins after the vehiclespeed is over 5 mph (8 km/h), by blinking the Seat BeltReminder Light and sounding an intermit
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
WARNING!• You can be badly injured working on or around amotor vehicle. Do only service work for which youhave the knowledge and the right equipment.I
Information Provided by:
IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 SUGGESTIONS FOR OBTAINING SERVICEFOR YOUR VEHICLE ...625▫ Prepare For The Appointment...
䡵 PUBLICATION ORDER FORMS ...630䡵 DEPARTMENT OF TRANSPORTATIONUNIFORM TIRE QUALITY GRADES ...631▫ Treadwear...6
SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you are having warranty work done, be sure to havethe right papers with
service. The manufacturer’s authorized dealer have thefacilities, factory-trained technicians, special tools, andthe latest information to ensure the
In Mexico contact:Av. Prolongacion Paseo de la Reforma, 1240Sante Fe C.P. 05109Mexico, D. F.In Mexico City: 5081-7568Outside Mexico City: 1-800-505-13
Seat Belts And Pregnant WomenWe recommend that pregnant women use seat beltsthroughout their pregnancy. Keeping the mother safe isthe best way to keep
The manufacturer will not stand behind any servicecontract that is not the manufacturer’s service contract. Itis not responsible for any service contr
MOPAR姞 PARTSMOPAR威 fluids, lubricants, parts, and accessories areavailable from an authorized dealer. They are recom-mended for your vehicle in order
PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Master-card, American Ex
Call toll free at:• 1–800–890–4038 (U.S.)• 1–800–387–1143 (Canada)OrVisit us on the Worldwide Web at:• www.techauthority.comDEPARTMENT OF TRANSPORTATI
Traction GradesThe Traction grades, from highest to lowest, are AA, A, B,and C. These grades represent the tire’s ability to stop onwet pavement, as m
INDEX10Information Provided by:
ABS (Anti-Lock Brake System) ...303Adding Engine Coolant (Antifreeze) ...579Adding Fuel ...510Additive
Fluid Level Check ...586Fluid Type ...585Special Additives ...585Autostick ...
Chart, Tire Sizing ...473Check Engine Light(Malfunction Indicator Light) ...311Checking Your Vehicle For Safety ...
Cruise Light ...306Cupholders ...188Customer Assistance ...625Data Recorder, E
Supplemental Restraint System (SRS) — Air BagsThis vehicle has Advanced Front Air Bags for both thedriver and right front passenger as a supplement to
Emergency Brake ...452Emergency, In Case ofJacking ...540Jump Starting ...548To
FiltersAir Cleaner ...569Air Conditioning ...402Engine Oil ...569Engine Oil Dispo
Requirements ...506Tank Capacity ...610Fueling ...510Fuses ...
Heated Seats...159Heater ...392Heater, Engine Block ...413High Beam Indica
Key, Replacement ...17Keys ...14Key, Sentry (Immobilizer) ...16Lane Change and
Illuminated Entry ...21Instrument Cluster ...167Interior ...171Lights On Reminder ..
Master Cylinder (Brakes) ...583Methanol ...507Mini-Trip Computer ...315Mirrors...
Oil Pressure Light ...301Onboard Diagnostic System ...562Operating Precautions ...562Operator
Rear Window Features ...293Rear Wiper/Washer...293Recorder, Event Data ...75Recreational To
Adjustable Upper Shoulder Anchorage ...55And Pregnant Women ...61Child Restraint ...76Extender ...
NOTE: The Driver and Passenger Advanced Front AirBags are certified to new Federal regulations.The Advanced Front Air Bags have a multistage inflatord
Shoulder Belt Upper Anchorage...55Side Airbag ...70Side Window Demisters (Defrosters) ...402Signals,
Theft System Arming ...20Theft System Disarming ...20Tilt Steering Column ...177Tip Start ..
Recreational ...532Weight ...519Towing Assistance...130Trac-Lok Rear Axle ...
Vanity Mirrors ...114Variance, Compass ...317Vehicle Identification Number (VIN) ...8Vehicle Lo
INSTALLATION OF RADIO TRANSMITTINGEQUIPMENTSpecial design considerations are incorporated into thisvehicle’s electronic system to provide immunity to
Patriot2013Information Provided by:13JK72-126-AB2nd EditionPrinted in U.S.A.Chrysler Group LLC
Air Bag System ComponentsYour vehicle may be equipped with the following air bagsystem components:• Occupant Restraint Controller (ORC)• Air Bag Warni
WARNING! (Continued)• Do not put anything on or around the air bagcovers or attempt to open them manually. You maydamage the air bags and you could be
Supplemental Seat-Mounted Side Air Bags(SAB) — If EquippedSupplemental Seat-Mounted Side Air Bags (SAB) mayprovide enhanced protection to help protect
Along with seat belts and pretensioners, Advanced FrontAir Bags work with the Supplemental Driver Side KneeAir Bag and the passenger side knee bolster
This Owner’s Manual has been prepared with the assis-tance of service and engineering specialists to acquaintyou with the operation and maintenance of
The side air bags will not deploy in all side collisions.Side air bag deployment will depend on the severity andtype of collision.Because air bag sens
WARNING!Ignoring the Air Bag Warning Light in your instru-ment panel could mean you won’t have the air bagsto protect you in a collision. If the light
Supplemental Seat-Mounted Side Air Bags (SAB)Inflator Units — If EquippedThe Supplemental Seat-Mounted Side Air Bags InflatorUnits (if equipped) are d
• Turn on the interior lights, which remain on as long asthe battery has power or until the ignition key isremoved.• Unlock the doors automatically.In
• As the air bags deflate you may see some smoke-likeparticles. The particles are a normal by-product of theprocess that generates the non-toxic gas u
WARNING! (Continued)• Do not attempt to modify any part of your air bagsystem. The air bag may inflate accidentally or maynot function properly if mod
WARNING! (Continued)•It is dangerous to try to repair any part of the air bagsystem yourself. Be sure to tell anyone who works onyour vehicle that it
Event Data Recorder (EDR)This vehicle is equipped with an event data recorder(EDR). The main purpose of an EDR is to record, incertain crash or near c
Child RestraintsEveryone in your vehicle needs to be buckled up at alltimes, including babies and children. Every state in theUnited States, and every
Summary Of Recommendations For Restraining Children In VehiclesChild Size, Height, Weight or Age Recommended Type of Child RestraintInfants and Toddle
Do not attempt sharp turns, abrupt maneuvers, or otherunsafe driving actions that can cause loss of vehiclecontrol. Failure to operate this vehicle sa
Infants And Child RestraintsSafety experts recommend that children ride rearward-facing in the vehicle until they are two years old or untilthey reach
Older Children And Child RestraintsChildren who are two years old or who have outgrowntheir rear-facing convertible child seat can ride forward-facing
Children Too Large For Booster SeatsChildren who are large enough to wear the shoulder beltcomfortably, and whose legs are long enough to bendover the
Recommendations For Attaching Child RestraintsRestraint Type CombinedWeight of theChild + ChildRestraintUse any attachment method shown with an “X” Be
Lower Anchors and Tethers for Children (LATCH)Restraint SystemYour vehicle is equipped with the child restraint anchor-age system called LATCH, which
LATCH Positions For Installing Child Restraints In This VehicleLatch Positions (Two-Door Models)Lower Anchorage Symbol 2 anchorages per seatingpositio
What is the weight limit (child’s weight +weight of the child restraint) for using theLATCH anchorage system to attach the childrestraint?65 lbs (29.5
Can two child restraints be attached using acommon lower LATCH anchorage?No Never “share” a LATCH anchorage withtwo or more child restraints. If the c
Locating The LATCH AnchoragesThe lower anchorages are round bars that arefound at the rear of the seat cushion where itmeets the seatback, below the a
Locating The LATCH AnchoragesIn addition, there are tether strap anchors lo-cated behind each rear seatback, near to thefloor.Latch Anchorages (Four-D
1INTRODUCTION 7Information Provided by:
LATCH-compatible child restraint systems will beequipped with a rigid bar or a flexible strap on each side.Each will have a hook or connector to attac
To Install A LATCH-compatible Child Restraint1. If the selected seating position has a Switchable Auto-matic Locking Retractor (ALR) seat belt, stow t
How To Stow An Unused ALR SeatbeltWhen using the LATCH attaching system to install achild restraint, stow all ALR seat belts that are not beingused by
Installing Child Restraints Using The Vehicle SeatBeltThe seat belts in the passenger seating positions areequipped with either a Switchable Automatic
Lap/Shoulder Belt Systems for Installing Child Restraints in this VehicleTwo-Door Models Four-Door Models92 THINGS TO KNOW BEFORE STARTING YOUR VEHICL
What is the weight limit (child’s weight +weight of the child restraint) for using theTether Anchor with the seat belt to attach aforward facing child
Installing A Child Restraint with a SwitchableAutomatic Locking Retractor (ALR)1. Place the child seat in the center of the seatingposition. For some
9. Test that the child restraint is installed tightly bypulling back and forth on the child seat at the beltpath. It should not move more than 1 inch
Any seat belt system will loosen with time, so check thebelt occasionally, and pull it tight if necessary.If the buckle or the cinching latch plate is
3. Attach the tether strap hook of the child restraint tothe top tether anchorage as shown in the diagram.4. Remove slack in the tether strap accordin
Commentaires sur ces manuels